Milling on the lathe

Get Info From Multiple Sources. An easy way to set up a lathe for milling. The lathe milling fixture complements the Versa-Mil and adds to the basic capabilities of the machine shop. If the Versa-Mil is out of action or being used for another job, many milling operations can still be accomplished by using the milling fixture (Figure 3-105).

Yes milling on the lathe is possible but with a lot of shortcomings and limitations.

The most critical is the rigidity. Only by looking the Optimum D18 or any other similar mini lathe you can tell that the capabilities are limited. A land drag I built to sell needed a lift mechanism, so I decided to put a window regulator motor on a trailer jack and make my own linear actuator. Yes, again as on lathe operations the same principles apply on milling too.

For brass always use good quality tools and razor sharp. In order to fit the vise to the top slide, I had to modify the toolpost tightening screw and clamp to clear the vise - now, the screw is attached to the handle, and the nut is in the slide - protruding a bit, but not so much as to interfere with the vise.

A resonably solid lathe can mill steel quite capably.

Accuracy within a thou of an inch is no problem. Before the advent of relatively cheap Asian milling machines it was quite common for this type of work to be carried out on a lathe. Get a set screw and drill and tap mark for center flat.

Put endmill into hole,line flat with setscrew and tighten! Here is your endmill holder! Your lathe is limite save for the biggest milling machine you can fit in your shop!

The mm HSS slot mill is spinning at 2RPM and taking a 0. Examples showing various methods of milling on the lathe. Milling Attachment for a lathe? I have attempted to show here how versatile working with a vertical slide can be and that it is not as limiting in terms of workpiece size as it often appears to be.

Notice that the highest point of the cutter matches with the highest point of the work piece. The cutter has been placed strategically that way. From the point “A” that the cutter begins to cut and until point “B” performs conventional milling when from point “B” to point “C” performs climb milling.

That one, and Workholding in the Lathe (same author) will give you a bunch of useful information, as well as pointing out the shortfalls of the method. I’ve made quite a few.

Anyways, if you pound those two titles into Amazon, you should get some. I was just wondering about milling projects you have done on a lathe. Personally I have done simple things such as milling a radius in the end of a square bar mounted in a quick change tool holder (with an end mill in the collet or chuck), and facing a block down to the required thickness when the Bridgeport is tied up. You can start a new project.

What are the limitations? The major difference between a milling machine and a lathe machine is the relationship of the workpiece and the tool.

In a lathe, the workpiece that is being machined spins about it’s axis, while the cutting tool does not. This is referred to as “turning”, and is effective for creating cylindrical parts.

The smallest milling machine might have inches in Y, and in X. For small work like a keyway in a shaft, they work great. Simple answer, yes you can mill on a lathe. Автор пина:Hector Lugo.

Recently I purchaced from ebay a dremel holder that can be attached to the toolpost of a lathe. Находите и прикалывайте свои пины в Pinterest! When milling on the lathe it would probably be best to remove the tailstock and make use of the far end of the bed.

I think one of your main issues will be snaking the belt around to the milling head. You may have to register before you can post: click the register link above to proceed.

An inexpensive way to do this is to mount an x-y table for a drill press 90deg upright on the cross slide, using a 4jaw as a collet. Pick a material to work on, set it on the lathe and start turning (milling) it to carve your own unique artifact.

Enjoy the fun of turning without the actual risk of getting injured. Remove the compound from the lathe and set in a milling attachment.

Clamp the barrel in the vise and locate the slot to mill and run the dovetail cutter in the jaw or collet at 2to 3RPM. Then push the barrel up or down through the cutter.